Note

Hello, welcome to the SunFounder Raspberry Pi & Arduino & ESP32 Enthusiasts Community on Facebook! Dive deeper into Raspberry Pi, Arduino, and ESP32 with fellow enthusiasts.

Why Join?

  • Expert Support: Solve post-sale issues and technical challenges with help from our community and team.

  • Learn & Share: Exchange tips and tutorials to enhance your skills.

  • Exclusive Previews: Get early access to new product announcements and sneak peeks.

  • Special Discounts: Enjoy exclusive discounts on our newest products.

  • Festive Promotions and Giveaways: Take part in giveaways and holiday promotions.

👉 Ready to explore and create with us? Click [here] and join today!

Lesson 18 74HC595¶

Introduction¶

Generally, there are two ways to drive a single 7-segment display. One way is to connect its 8 pins directly to eight ports on the Uno board, which we have done previously. Or you can connect the 74HC595 to three ports of the UNO board and then the 7-segment display to the 74HC595. In this experiment, we will use the latter. By this way, we can save five ports - considering the Uno board’s limited ports, this is very important. Now let’s get started!

Components¶

../_images/uno22.png

Schematic Diagram¶

In the experiment MR (pin10) is connected to 5V (HIGH Level) and OE (pin 1) to GND (LOW Level). Therefore, the data is input into the rising edge of SHcp and enters the memory register through the rising edge. We use the shiftout() function to output a 8-bit data to the shift register through DS. In the rising edge of the SHcp, the data in the shift register moves successively one bit in one time, i.e. data in Q1 moves to Q2, and so forth. In the rising edge of STcp, data in the shift register moves into the memory register. All data will be moved to the memory register after 8 times. Then the data in the memory register is output to the bus (Q0-Q7). So the 16 characters are displayed in the 7-segment in turn.

../_images/image164.png

Experimental Procedures¶

Step 1: Build the circuit (pay attention to the direction of the chip by the concave on it)

7-Segment

74HC595

Uno Kit

a

Q7

b

Q6

c

Q5

d

Q4

e

Q3

f

Q2

g

Q1

DP

Q0

VCC

5V

DS

11

CE

GND

ST

12

SH

8

MR

5V

Q7’

N/C

GND

GND

GND

../_images/image165.png

Step 2: Open the code file.

Step 3: Select the Board and Port.

Step 4: Upload the sketch to the board.

You should now see the 7-segment display from 0 to 9 and A to F.

../_images/image166.jpeg

Code¶

Code Analysis¶

Set the array elements

int datArray[16] = {252, 96, 218, 242, 102, 182, 190, 224, 254, 246, 238, 62, 156, 122, 158, 142};

This array stores the data of the 16 characters from 0 to F. 252 stands for 0, which you can calculate by yourself. To display 0, the segment g (the middle one) of the 7-segment display must be low level (dim).

Since the segment g is connected to Q1 of the 74HC595, set both Q1 and DP (the dot) as low level and leave the rest pins as high level. Therefore, the values of Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 are 1 1 1 1 1 1 0 0.

Change the binary numbers into decimal ones: 1x27+1x26+1x25+1x24+1x23+1x22+0x21+1x20=252.

So that’s the value for the number 0 to be displayed. You can calculate other characters similarly.

Display 0-F in the 7-segment display

for(int num = 0; num < 16; num++)

{

  digitalWrite(STcp,LOW); //ground ST_CP and hold low for as long as you are transmitting

  shiftOut(DS,SHcp,MSBFIRST,datArray[num]);

  //return the latch pin high to signal chip that it

  //no longer needs to listen for information

  digitalWrite(STcp,HIGH); //pull the ST_CPST_CP to save the data

  delay(1000); //wait for a second

}

Set STcp as low level first and then high level. It will generate a rising edge pulse of STcp.

shiftOut() is used to shift out a byte of data one bit at a time, which means to shift a byte of data in dataArray[num] to the shifting register with the DS pin. MSBFIRST means to move from high bits.

After digitalWrite(STcp,HIGH) is run, the STcp will be at the rising edge. At this time, the data in the shift register will be moved to the memory register.

A byte of data will be transferred into the memory register after 8 times. Then the data of memory register is output to the bus (Q0-Q7). You will see a character is displayed on the 7-segment. Then delay for 1000ms. After that line, go back to for(). The loop repeats until all the characters are displayed in the 7-segment display one by one after 16 times.