Note

Hello, welcome to the SunFounder Raspberry Pi & Arduino & ESP32 Enthusiasts Community on Facebook! Dive deeper into Raspberry Pi, Arduino, and ESP32 with fellow enthusiasts.

Why Join?

• Expert Support: Solve post-sale issues and technical challenges with help from our community and team.

• Learn & Share: Exchange tips and tutorials to enhance your skills.

• Exclusive Previews: Get early access to new product announcements and sneak peeks.

• Special Discounts: Enjoy exclusive discounts on our newest products.

• Festive Promotions and Giveaways: Take part in giveaways and holiday promotions.

👉 Ready to explore and create with us? Click [here] and join today!

8. Self-Driving Car

This project is a combination of the two projects 6. Play with Ultrasonic Module and 5. Play with Obstacle Avoidance Module. 2 infrared obstacle avoidance modules do short distance or edge detection, and ultrasonic modules do long distance detection to confirm that the car does not hit an obstacle during the free driving process.

Required Components

In this project, we need the following components.

It’s definitely convenient to buy a whole kit, here’s the link:

Name	ITEMS IN THIS KIT	LINK
3 in 1 Starter Kit	380+	3 in 1 Starter Kit

You can also buy them separately from the links below.

COMPONENT INTRODUCTION	PURCHASE LINK
SunFounder R3 Board	BUY
L9110 Motor Driver Module	-
TT Motor	-
Ultrasonic Module	BUY
Obstacle Avoidance Module	BUY

Wiring

Connect the ultrasonic module and the 2 IR obstacle avoidance modules at the same time.

Wire the ultrasonic to the R3 board as follows.

Ultrasonic Module	R3 Board
Vcc	5V
Trig	3
Echo	4
Gnd	GND

The wiring of the 2 IR obstacle avoidance modules to the R3 board is as follows.

Left IR Module	R3 Board
OUT	8
GND	GND
VCC	5V

Right IR Module	R3 Board
OUT	7
GND	GND
VCC	5V

Code

Note

• Open the 8.self_driving_car.ino file under the path of 3in1-kit\car_project\8.self_driving_car.

• Or copy this code into Arduino IDE.

• Or upload the code through the Arduino Web Editor.

The car will drive freely once the code has been uploaded successfully. When the IR obstruction module on both sides detects an obstacle, it will move in the opposite direction for emergency evasion; if there is an obstacle within 2~10cm directly in front of the car, it will back up to the left, adjust its direction, and then move forward.

How it works?

The workflow of this project is as follows.

• Priority read the value of left and right IR obstacle avoidance module.

• If the left IR module is 0 (obstacle detected), the right IR module is 1, let the car back up to the left.

• If the right IR module is 0 (obstacle detected), let the car back up to the right.

• If 2 IR modules detect the obstacle at the same time, the car will back up.

• Otherwise read the distance detected by the ultrasonic module.

• If the distance is greater than 50cm, let the car go forward.

• If the distance is between 2-10cm, let the car backward before turning.

• If the distance is between 10-50cm, let the car go forward at low speed.

void loop() {

    int left = digitalRead(leftIR);   // 0: Obstructed  1: Empty
    int right = digitalRead(rightIR);

    if (!left && right) {
        backLeft(150);
    } else if (left && !right) {
        backRight(150);
    } else if (!left && !right) {
        moveBackward(150);
    } else {
        float distance = readSensorData();
        Serial.println(distance);
        if (distance > 50) { // Safe
            moveForward(200);
        } else if (distance < 10 && distance > 2) { // Attention
            moveBackward(200);
            delay(1000);
            backLeft(150);
            delay(500);
        } else {
            moveForward(150);
        }
    }
}